Cockburn (South Australia) – Lead
NON POTABLE WATER SUPPLY
June 27 2017: Cockburn (South Australia) – Lead 0.0164mg/L
Based on health considerations, the concentration of lead in drinking water should not
exceed 0.01 mg/L.
“… Lead can be present in drinking water as a result of dissolution from natural sources, or from household plumbing systems containing lead. These may include lead in pipes, or in solder used to seal joints. The amount of lead dissolved will depend on a number of factors including pH, water hardness and the standing time of the water.
Lead is the most common of the heavy metals and is mined widely throughout the world. It is used in the production of lead acid batteries, solder, alloys, cable sheathing, paint pigments, rust inhibitors, ammunition, glazes and plastic stabilisers. The organo-lead compounds tetramethyl and tetraethyl lead are used extensively as anti-knock and lubricating compounds in gasoline…
Lead can be absorbed by the body through inhalation, ingestion or placental transfer. In adults,
approximately 10% of ingested lead is absorbed but in children this figure can be 4 to 5 times higher. After absorption, the lead is distributed in soft tissue such as the kidney, liver, and bone marrow where it has a biological half-life in adults of less than 40 days, and in skeletal bone where it can persist for 20 to 30 years.
In humans, lead is a cumulative poison that can severely affect the central nervous system. Infants, fetuses and pregnant women are most susceptible. Placental transfer of lead occurs in humans as early as the 12th week of gestation and continues throughout development.
Many epidemiological studies have been carried out on the effects of lead exposure on the intellectual development of children. Although there are some conflicting results, on balance the studies demonstrate that exposure to lead can adversely affect intelligence.
These results are supported by experiments using young primates, where exposure to lead causes significant behavioural and learning difficulties of the same type as those observed in children.
Other adverse effects associated with exposure to high amounts of lead include kidney damage, interference with the production of red blood cells, and interference with the metabolism of calcium needed for bone formation…” ADWG 2011
Cockburn (South Australia) – Copper
NON POTABLE WATER SUPPLY
June 27 2017: Cockburn (South Australia) – Copper 1.185mg/L
Based on health considerations, the concentration of copper in drinking water should not
exceed 2 mg/L.
Based on aesthetic considerations, the concentration of copper in drinking water should
not exceed 1 mg/L.
Copper is widely distributed in rocks and soils as carbonate and sulfide minerals.
Copper is relatively resistant to corrosion and is used in domestic water supply pipes and fittings. It is also used in the electroplating and chemical industries, and in many household goods. Copper sulfate is used extensively to control the growth of algae in water storages.
Copper is present in uncontaminated surface waters at very low concentrations, usually less than 0.01 mg/L. The concentration can rise substantially when water with a low pH and hardness remains in stagnant contact with copper pipes and fittings. Under these conditions, the concentration of copper can reach 5 mg/L or higher. In one extreme case overseas, a concentration of 22 mg/L was reported.
Cockburn – South Australia – Temperature
NON POTABLE DRINKING WATER
November 29 2016: Cockburn (South Australia) – Temperature 25C
February 7 2017: Cockburn (South Australia) – Temperature 29C
“No guideline is set due to the impracticality of controlling water temperature.
Drinking water temperatures above 20°C may result in an increase in the number of
Temperature is primarily an aesthetic criterion for drinking water. Generally, cool water is more palatable than warm or cold water. In general, consumers will react to a change in water temperature. Complaints are most frequent when the temperature suddenly increases.
The turbidity and colour of filtered water may be indirectly affected by temperature, as low water temperatures tend to decrease the efficiency of water treatment processes by, for instance, affecting floc formation rates and sedimentation efficiency.
Chemical reaction rates increase with temperature, and this can lead to greater corrosion of pipes and fittings in closed systems. Scale formation in hard waters will also be greater at higher temperatures…
Water temperatures in major Australian reticulated supplies range from 10°C to 30°C. In some long, above-ground pipelines, water temperatures up to 45°C may be experienced…
The effectiveness of chlorine as a disinfectant is influenced by the temperature of the water being dosed. Generally higher temperatures result in more effective disinfection at a particular chlorine dose, but this may be counterbalanced by a more rapid loss of chlorine to the atmosphere (AWWA 1990).
Chlorine reacts with organic matter in water to produce undesirable chlorinated organic by-products, and higher temperatures increase the rate of these reactions.
Temperature can directly affect the growth and survival of microorganisms. In general the survival time of infectious bacteria and parasites is reduced as the temperature of the contaminated water increases.
Australian Drinking Water Guidelines 2011