McLaren Vale  (South Australia) – Ammonia

2022/23: McLaren Vale (South Australia) Ammonia – Free – as NH3 0.51mg/L (max), 0.35mg/L (av.)

Based on aesthetic considerations (corrosion of copper pipes and fittings), the concentration
of ammonia (measured as ammonia) in drinking water should not exceed 0.5 mg/L.
No health-based guideline value is set for ammonia.

“…Most uncontaminated source waters have ammonia concentrations below 0.2 mg/L. High concentrations (greater than 10 mg/L) have been reported where water is contaminated with animal waste. Ammonia is unlikely to be detected in chlorinated supplies as it reacts quickly with free chlorine. Ammonia in water can result in the corrosion of copper pipes and fittings, causing copper stains on sanitary ware. It is also a food source for some microorganisms, and can support nuisance growths of bacteria and algae, often with a resultant increase in the nitrite concentration.” ADWG 2011

McLaren Vale (South Australia) – Bromodichloromethane

2022/23: McLaren Vale (South Australia) Bromodichloromethane 87ug/L (max), 64.33ug/L (av.)

WHO Guideline level BDCM: 60ug/L (Australian Guideline for BDCM is included in the Trihalomethane (THM) combined total of BDCM, Chloroform, Dibromochloromethane and Bromoform. THM guideline is 250ug/L)

“Carcinogenicity : Bromodichloromethane is reasonably anticipated to be a human carcinogen based on sufficient evidence of carcinogenicity from studies in experimental animals.
Cancer Studies in Experimental Animals: Oral exposure to bromodichloromethane caused tumors at several different tissue sites in mice and rats. Administration of bromodichloromethane by stomach tube caused benign and malignant kidney tumors (tubular-cell adenoma and adenocarcinoma) in male mice and in rats of both sexes, benign and
malignant liver tumors (hepatocellular adenoma and carcinoma) in female mice, and benign and malignant colon tumors (adenomatous polyps and adenocarcinoma) in rats of both sexes (NTP 1987, ATSDR 1989, IARC 1991, 1999).

2022/23: McLaren Vale (South Australia) – pH (alkaline)

2022/23: McLaren Vale (South Australia) pH 8.99 (av.)

Based on the need to reduce corrosion and encrustation in pipes and fittings, the pH of
drinking water should be between 6.5 and 8.5.

New concrete tanks and cement-mortar lined pipes can significantly increase pH and
a value up to 9.2 may be tolerated, provided monitoring indicates no deterioration in
microbiological quality.

pH is a measure of the hydrogen ion concentration of water. It is measured on a logarithmic scale from 0 to 14. A pH of 7 is neutral, greater than 7 is alkaline, and less than 7 is acidic.

One of the major objectives in controlling pH is to minimise corrosion and encrustation in pipes and fittings. Corrosion can be reduced by the formation of a protective layer of calcium carbonate on the inside of the pipe or fitting, and the formation of this layer is affected by pH, temperature, the availability of calcium (hardness) and carbon dioxide. If the water is too alkaline (above pH 8.5), the rapid deposition and build-up of calcium carbonate that can result may eventually block the pipe.

2022/23: McLaren Vale (South Australia). Ammonia, Bromodichloromethane, pH

McLaren Vale  (South Australia) – Ammonia

2022/23: McLaren Vale (South Australia) Ammonia – Free – as NH3 0.51mg/L (max), 0.35mg/L (av.)

Based on aesthetic considerations (corrosion of copper pipes and fittings), the concentration
of ammonia (measured as ammonia) in drinking water should not exceed 0.5 mg/L.
No health-based guideline value is set for ammonia.

“…Most uncontaminated source waters have ammonia concentrations below 0.2 mg/L. High concentrations (greater than 10 mg/L) have been reported where water is contaminated with animal waste. Ammonia is unlikely to be detected in chlorinated supplies as it reacts quickly with free chlorine. Ammonia in water can result in the corrosion of copper pipes and fittings, causing copper stains on sanitary ware. It is also a food source for some microorganisms, and can support nuisance growths of bacteria and algae, often with a resultant increase in the nitrite concentration.” ADWG 2011

McLaren Vale (South Australia) – Bromodichloromethane

2022/23: McLaren Vale (South Australia) Bromodichloromethane 87ug/L (max), 64.33ug/L (av.)

WHO Guideline level BDCM: 60ug/L (Australian Guideline for BDCM is included in the Trihalomethane (THM) combined total of BDCM, Chloroform, Dibromochloromethane and Bromoform. THM guideline is 250ug/L)

“Carcinogenicity : Bromodichloromethane is reasonably anticipated to be a human carcinogen based on sufficient evidence of carcinogenicity from studies in experimental animals.
Cancer Studies in Experimental Animals: Oral exposure to bromodichloromethane caused tumors at several different tissue sites in mice and rats. Administration of bromodichloromethane by stomach tube caused benign and malignant kidney tumors (tubular-cell adenoma and adenocarcinoma) in male mice and in rats of both sexes, benign and
malignant liver tumors (hepatocellular adenoma and carcinoma) in female mice, and benign and malignant colon tumors (adenomatous polyps and adenocarcinoma) in rats of both sexes (NTP 1987, ATSDR 1989, IARC 1991, 1999).

2022/23: McLaren Vale (South Australia) – pH (alkaline)

2022/23: McLaren Vale (South Australia) pH 8.99 (av.)

Based on the need to reduce corrosion and encrustation in pipes and fittings, the pH of
drinking water should be between 6.5 and 8.5.

New concrete tanks and cement-mortar lined pipes can significantly increase pH and
a value up to 9.2 may be tolerated, provided monitoring indicates no deterioration in
microbiological quality.

pH is a measure of the hydrogen ion concentration of water. It is measured on a logarithmic scale from 0 to 14. A pH of 7 is neutral, greater than 7 is alkaline, and less than 7 is acidic.

One of the major objectives in controlling pH is to minimise corrosion and encrustation in pipes and fittings. Corrosion can be reduced by the formation of a protective layer of calcium carbonate on the inside of the pipe or fitting, and the formation of this layer is affected by pH, temperature, the availability of calcium (hardness) and carbon dioxide. If the water is too alkaline (above pH 8.5), the rapid deposition and build-up of calcium carbonate that can result may eventually block the pipe.